Работы по гидроизоляции проводить при температуре поверхности конструкции от +5 до + 35 °С.
РАСХОД СУХОЙ СМЕСИ: 1,9 кг/дм3.
ПОДГОТОВКА ПОЛОСТИ ТЕЧИ: Увеличить полость течи с помощью отбойного молотка на ширину не менее 25 мм и глубину не менее 50 мм с расширением вглубь («ласточкин хвост»). Тщательно очистить щеткой с металлическим ворсом.
ПРИГОТОВЛЕНИЕ РАСТВОРНОЙ СМЕСИ: Использовать только чистую тару и воду. Смешать с водой в пропорции 0,22 л воды на 1 кг сухой смеси или 1 часть воды на 4 части сухой смесипо объему. При температурах близких к 0 °С использовать теплую воду. Использовать за 30 секунд.
ОСТАНОВКА ТЕЧИ: Сформировать плотный конус из приготовленной растворной смеси. С максимально возможным усилием вдавить конус в полость течи и удерживать 1 минуту. При наличии нескольких напорных течей работы начинать с верхней. Удалить излишки растворной смеси «Пенеплаг» до половины полости течи. Обработать полость остановленной течи растворной смесью «Пенетрон». Оставшийся объем полости заполнить растворной смесью «Пенекрит». Через 1-2 часа поверхность раствора «Пенекрит» и прилегающую к ней бетонную поверхность обработать растворной смесью «Пенетрон» в два слоя.
УХОД ЗА ОБРАБОТАННОЙ ПОВЕРХНОСТЬЮ: Увлажнять и защищать поверхность от механических воздействий, отрицательных температур и осадков в течение 3-х суток.
МЕРЫ ПРЕДОСТОРОЖНОСТИ: Использовать перчатки резиновые, перчатки х/б, респиратор, очки защитные, спецодежду из плотной ткани, сапоги. При попадании смеси на кожу или в глаза немедленно промыть водой и обратиться к врачу.
PENEPLUG® is a rapid setting, integral crystalline cementitious waterstop designed to stop active water leaks and moisture ingress.
RECOMMENDED FOR
PENEPLUG® can be used internally or externally as a waterproof plugging mortar or where rapid setting and early strength gain is required.
Plugging/stopping active water leaks
Sealing of leaking joints, form tie holes or cracks PENEPLUG® can be used on the following substrates:
Concrete
Masonry
Earthenware
Stone
ADVANTAGES
Stops water flow
Sets in approximately 30 seconds after mixing
Durable
Can be used underwater
Can be mixed with water or used dry
Easy to apply
Packaged in easy to use, re-sealable containers
Zero VOC - PENETRON powdered products contain zero volatile organic compounds and are safe for use both outdoors and in confined indoor spaces.
DIRECTIONS FOR USE
Surface Preparation: The substrate must be clean, sound and free of any surface contamination, such as oils, coatings, paints, dirt, etc. Leaking areas must be cut back to sound material, leaving an appropriate chase for receiving PENEPLUG®.
Mixing: Setting time is dependent largely on the amount of mixing water used. Standard mixing ratio at 20°C is 1.1 kg PENEPLUG® and approximately 1 cup (0.25 l) of water. Water must be added to PENEPLUG® and mixed quickly. The mix should have a dry pack (dry earth) consistency, holding a shape when squeezed in your hand but easily crumbled when pressed with fingers. Mixing time is about 15 seconds with setting occurring about 30 seconds later. In cold weather, use lukewarm water. In higher temperatures, use cold water.
Application: To avoid waste, only small quantities of PENEPLUG® should be mixed. After mixing, apply PENEPLUG® to the appropriate area immediately. Material should be formed into a wedge and forced into the leak. This can be accomplished with the use of a block of wood and hammer. Work the plug well into the area and then, applying as much pressure as possible, hold firmly in place for about 30 seconds or until set. After the leak has stopped, prime the area with a bond coat of PENETRON® and then fill the remaining void to the surface with PENECRETE MORTAR™. Remove excess material. After lightly pre-wetting, apply a final coat of PENETRON® to the repaired area. In certain circumstances PENEPLUG® may be applied as a dry powder. After preparing the surface as described above, place and hold the powder directly over the leak for 30-60 seconds.
PACKAGING This product can be purchased in 25 kg pails and 4 kg pails.
STORAGE / SHELF LIFE
PENEPLUG® should be stored dry at a minimum temperature of 5°C. When properly stored in a dry cool place in unopened and undamaged original packaging, shelf life is 18 months.
SAFE HANDLING INFORMATION
PENEPLUG® contains cement which is alkaline. Will irritate eyes and skin and may cause skin sensitization. Wear appropriate eye, skin and breathing protection when using this product. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. For further information please refer to Material Safety Data Sheet.
